LEXUS RX 300

1998-2003 of release

Repair and car operation



Lexus RX 300
+ Cars Lexus RX-300
+ Controls and operation receptions
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, heating, ventilation and air conditioning
+ The power supply system and release of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Automatic transmission and interaxal differential
+ Transmissionnaja line
+ Brake system
+ Suspension bracket and steering
- Body
   + The external equipment and кузовные elements
   - The salon equipment
      Removal and installation of the panel of devices and the main ware box
      Removal of a carpet covering of a floor and ware box of the central console
      Removal and installation of furnish of a ceiling
      Removal, dismantling, assemblage and installation of forward seats
      Removal, dismantling, assemblage and installation of back seats
      Removal and installation of seat belts and their emergency натяжителей
+ Onboard electric equipment
+ Basic schemes of electric connections


лечение спины


The salon equipment

Removal and installation of the panel of devices and the main ware box

Components of the panel of devices

1 — the Intensifying bar
2 — the Returnable spring of a pedal
3 — Assemblage of a pillow of safety of the forward passenger
4 — the Arm №2
5 — the Arm №1
6 — the Panel №1 dynamics
7 — ECU ABS
8 — the Overlay of the panel of devices
9 — ECU bodies
10 — Assemblage of the multipurpose display
11 — the Panel of furnish of the central console
12 — Lateral segments separate the central console
13 — audiosystem Assemblage
14 — the Air line
15 — the Bottom segment of furnish of the central section of the panel of devices
16 — the Fringing
17 — the Panel of furnish of the lock of ignition
18 — the Bottom panel of the central section of the panel of devices
19 — Assemblage of the lever of the selector of modes АТ

20 — the Panel of furnish of the bottom console
21 — the Bottom insert
22 — Podrulevaja the panel
23 — the Bottom holder №2
24 — the Bottom holder №1
25 — the Combination of devices
26 — Furnish of a forward rack of a body
27 — Furnish of a combination of devices
28 — the Bottom panel №2
29 — CD-changer
30 — the Lateral segment of the panel of devices (right)
31 — the Combined switch
32 — the Bottom cover №2
33 — the Bottom lateral panel
34 — the Lateral segment of the panel of devices (left)
35 — Casings of a steering column
36 — the Steering wheel
37 — Furnish of a threshold of a forward door
38 — a steering wheel Overlay

Components of a path of system of ventilation

1 — Furnish дефлектора обдува a windscreen
2 — Assemblage дефлектора обдува a windscreen
3 — the Overlay of the panel of devices
4 — Zaslonka №4
5 — Lateral дефлектор №2
6 — Electroconducting
7 — the Air line №5 lateral дефлектора
8 — the Air line lateral дефлектора №2
9 — the Air line from a heater to заслонке №4

10 — the Central air line from a heater to заслонке
11 — fixture Assemblage in a ware box
12 — the Central arm
13 — the Air line from a heater to заслонке №1
14 — the Air line lateral дефлектора №1
15 — the sun Gauge
16 — the Gauge of automatic control of illumination
17 — the Arm №1
18 — Lateral дефлектор №1
19 — Zaslonka №1


On сопр. Illustrations the type of fixture of the listed components also is specified: letters with A on F designate bolts and screws, by letters G and H – nuts, instead of the components designated by letters fasten clamps.


 PERFORMANCE ORDER

  1. Consistently remove components 30, 34, 37, 26, 33, 6 and 32 panels of devices, having liberated them from clamps.
  1. Separate a socket of a pillow of safety, trying not to damage electroconducting.
  1. Remove the bottom panel №2, having turned out 2 bolts and 2 screws.
  1. At a corresponding complete set turn out 4 nuts, separate a socket and remove CD-changer.
  1. Turn out 2 bolts and 2 nuts and remove assemblage of a pillow of safety.

After removal lay assemblage of a pillow of safety by a face sheet upwards. Do not assort assemblage of a pillow of safety. At installation tighten fixture with demanded efforts, assemblage of a pillow of safety with visible damages replace, do not suppose short circuit of electroconducting of a pillow of safety.

  1. Remove a steering wheel with an overlay, and also casings of a steering column (see Has undressed Removal, installation, dismantling and assemblage of a steering column).
  2. Consistently remove components 17, 20, 22 and 21 panels of devices, having liberated them from clamps and having turned out in last two cases on 2 bolts.
  3. Remove a steering column (see Has undressed Removal, installation, dismantling and assemblage of a steering column).
  4. Consistently remove components 16, 12 and 18 panels of devices, having liberated them from clamps and having turned out in the latter case 6 screws.
  1. Turn out 4 bolts and remove the panel of furnish of the central console.
  1. Separate sockets, turn out on 4 bolts and remove assemblages of the multipurpose display and an audiosystem.
  1. Turn out 2 screws and remove furnish of a combination of devices.
  1. Separate a socket, turn out 3 screws and remove a combination of devices.
  2. Turn out two bolts and remove the bottom holders (23 and 24).
  3. Separate a socket, disconnect draught, give 4 nuts and remove assemblage of the lever of selector AT.
  4. Remove air lines.
  1. Separate sockets, turn out 2 bolts and 2 nuts and remove an overlay of the panel of devices.
  1. Give fixture and remove arms №1 and №2 (4 and 5).
  2. Turn out on 2 nuts and remove modules of management of a body and ABS.
  3. Remove a returnable spring, turn out a bolt, 2 nuts and remove the block of the relay and safety locks under the panel of devices.
  1. Turn out 4 bolts and 4 nuts and remove an intensifying bar.
  1. Consistently remove components №№ 11, 12, 18, 5, 1, 2, 7, 14, 8, 13, 9, 19, 4, and 10.
  1. Turn out 5 screws, wring out clamps and remove electroconducting.
  1. Turn out 2 screws and remove an arm №1.
  2. Remove the gauge of the sun and the gauge of automatic control of illumination.
  3. Installation is made upside-down. Tighten fixture with demanded efforts, replace the deformed clamps.