LEXUS RX 300

1998-2003 of release

Repair and car operation



Lexus RX 300
+ Cars Lexus RX-300
+ Controls and operation receptions
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, heating, ventilation and air conditioning
+ The power supply system and release of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Automatic transmission and interaxal differential
+ Transmissionnaja line
+ Brake system
+ Suspension bracket and steering
- Body
   - The external equipment and кузовные elements
      Removal and installation top spacers an impellent compartment
      Removal and installation of bumpers
      Removal and installation of a cowl, its lock and decorative lattice of a radiator
      Removal, installation, dismantling and assemblage of a forward door and its components
      Removal, installation, dismantling and assemblage of a back door and its components
      Removal, dismantling, assemblage and installation of a door of a back and its components
      Removal and installation of cleaners and обтекателя a windscreen
      Removal and installation moldingов
      Removal and spoiler installation
      Removal and installation of the top hatch
   + The salon equipment
+ Onboard electric equipment
+ Basic schemes of electric connections


Èíòåðåñíîå: https://welx.net


Removal, installation, dismantling and assemblage of a forward door and its components

Removal and adjustment

The driver's door is more low considered; removal and installation of the right door is made similarly.

Components of installation and assemblage of a forward door and external rear-view mirror

1 — Molding
2 — Directing glasses
3 — the Bottom section of a frame
4 — the External handle of a door
5 — Zaglushka
6 — the lock Cylinder
7 — Glass
8 — the External rear-view mirror
9 — a frame Overlay
10 — the Loop
11 — the Terminator
12 — a lock Cover

13 — the Lock
14 — door Consolidation
15 — Pillows
16 — Steklopodyomnik
17 — the Internal lever of unlocking of the lock
18 — the Cover of a service aperture
19 — Dinamik
20 — the Internal panel of furnish of a door
21 — the Fixture
22 — the Bottom consolidation of a door
23 — the Edging of the internal lever of unlocking of the lock
24 — the Switch window raiserов


 PERFORMANCE ORDER

  1. Remove заглушку, turn out the screw and remove an edging of the internal lever of unlocking of the lock of a forward door by means of a screw-driver.
  2. Wring out clamps and remove the control panel window raiserми and locks of doors.
  3. Take from a covering of a door the fixture and separate its electroconducting.
  1. Turn out screws and remove clamps.
  1. Insert a screw-driver between a door and its furnish and wring out the furnish panel.
  2. Remove the panel of furnish of a door together with consolidation. Replace its clamps and remove consolidation.
  3. Turn out the screw of fastening of the lever of unlocking of the lock, disconnect from the lever two cables and remove the lever.

At mirror removal this procedure is not obligatory.

  1. Separate a socket, turn out 3 bolts and remove speaker.

At mirror removal this procedure is not obligatory.

  1. Remove two plugs and a cover of a service aperture.
  1. Remove molding.

At mirror removal this procedure is not obligatory.

  1. Remove a clamp, and disconnect from a door a frame overlay.
  2. Separate a rear-view mirror socket, turn out 3 bolts and remove a mirror.
  3. Lower glass so that in a service aperture bolts of its fastening were visible. Turn out bolts and take out glass from a door.
  4. Remove directing glasses.
  5. Separate a socket, turn out 6 bolts and remove window raiser through a service aperture.

Necessarily separate a socket to exclude operation possibility window raiser and trauma receptions.

  1. Turn out the screw and remove the bottom section of a frame.
  2. Disconnect from the external handle and the cylinder of the lock two draughts. Turn out 4 screws, separate two sockets and remove the lock through a service aperture. Turn out 2 screws and uncover the lock.
  3. Remove заглушку, turn out two bolts and remove the external handle of a door with the lock cylinder.
  4. Turn out a bolt and remove the cylinder of the lock from the door handle.
  5. Remove consolidation and basic pillows.
  6. Give fixture of loops and the terminator of a door and remove a door.
  7. At installation of the door especially new, it is necessary to adjust its position.

At use of centering bolts for fastening of loops of a door to adjust its position it will not be possible. For adjustment replace aligning bolt with a usual bolt with a washer.

  1. For door adjustment in directions forward/back and upwards/downwards give bolts of fastening of loops to a body, expose a door in demanded position and tighten bolts with effort of 23 Nanometers.
  2. For door adjustment in directions upwards/downwards and inside/outside give bolts of fastening of loops to a door, expose a door in demanded position and tighten bolts with effort of 27 Nanometers.
  3. If necessary adjust position of the drummer of the lock, moving it (tapping with a hammer) at the released fixture outside/inside and upwards/downwards. Preliminary uncover the drummer. Upon termination of adjustment tighten bolts of fastening of the drummer with effort of 23 Nanometers and establish a cover of the drummer.

Replacement of an external rear-view mirror

 PERFORMANCE ORDER

  1. Wind a mirror with rags and pull for its bottom edges, liberating a mirror from clamps.
  1. Remove a mirror, having separated its socket.
  2. At installation join a socket, establish a mirror in the top clamps and fix it in the bottom clamps.

Installation

 PERFORMANCE ORDER

  1. Installation is made upside-down.
  2. Tighten fixture with demanded efforts, use new clamps.
  3. The description of installation of an overlay of a frame is more low resulted:
    • Heat up the adjusting panel of a door to temperature 40 ÷ 60 hailstones.;
    • Remove from a door a sticky strip and clear a door of its rests;
    • At an overlay reuse heat up it to temperature 20 ÷ 30 hailstones., clear it of traces of a sticky strip and put a new strip in width of 5 mm;
    • Brush put on an adjusting surface of a door a first coat (Primer M) and allow it to dry up within 3 minutes;
    • Again heat up a door to temperature 40 ÷ 60 hailstones., and an overlay of a frame to 20 ÷ 30 hailstones.;
    • Remove a protective film from a sticky strip of an overlay and press an overlay to a door;
    • Establish an angular clamp of an overlay.