LEXUS RX 300

1998-2003 of release

Repair and car operation



Lexus RX 300
+ Cars Lexus RX-300
+ Controls and operation receptions
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, heating, ventilation and air conditioning
+ The power supply system and release of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Automatic transmission and interaxal differential
+ Transmissionnaja line
+ Brake system
+ Suspension bracket and steering
- Body
   - The external equipment and кузовные elements
      Removal and installation top spacers an impellent compartment
      Removal and installation of bumpers
      Removal and installation of a cowl, its lock and decorative lattice of a radiator
      Removal, installation, dismantling and assemblage of a forward door and its components
      Removal, installation, dismantling and assemblage of a back door and its components
      Removal, dismantling, assemblage and installation of a door of a back and its components
      Removal and installation of cleaners and обтекателя a windscreen
      Removal and installation moldingов
      Removal and spoiler installation
      Removal and installation of the top hatch
   + The salon equipment
+ Onboard electric equipment
+ Basic schemes of electric connections




Removal, installation, dismantling and assemblage of a back door and its components

The left door is more low considered; removal and installation of the right door is made similarly.

Components of a back door

1 — Consolidation of the fixed glass
2 — Directing glasses
3 — the Fixed glass of a back door
4 — Glass
5 — Molding
6 — the External handle
7 — the Lock
8 — a lock Casing
9 — the Dividing lath
10 — Steklopodyomnik
11 — door Consolidation

12 — Pillows
13 — the Loop
14 — the Terminator
15 — the Block of management of a back door
16 — the Cover of a service aperture
17 — the Internal lever of unlocking of the lock
18 — Internal consolidation
19 — Dinamik
20 — the Internal panel of furnish of a door
21 — the Edging of the internal lever of unlocking of the lock
22 — the Switch window raiser


 PERFORMANCE ORDER

  1. Remove заглушку, turn out the screw and remove an edging of the internal lever of unlocking of the lock of a back door by means of a screw-driver.
  2. Wring out clamps and remove the control panel window lift.
  1. Remove заглушки screws, turn out screws and remove clamps.
  1. Insert a screw-driver between a door and its furnish and wring out the furnish panel.
  2. Remove the panel of furnish of a door together with consolidation. Replace its clamps and remove consolidation.
  3. Separate two sockets, liberate electroconducting of the block of management from the holder, turn out two screws and remove the block of management of a back door.
  4. Separate a socket, turn out 3 bolts and remove speaker.
  5. Turn out the screw of fastening of the lever of unlocking of the lock, disconnect from the lever two cables and remove the lever.
  6. Remove two plugs and a cover of a service aperture.
  7. Remove consolidation.
  8. Lower glass so that in a service aperture bolts of its fastening were visible. Give nuts, take glass from holders and lower it in a door.

Preliminary lay in a door rags not to scratch glass. Arrange glass as it is possible more close to forehand for a door.

  1. Turn out two bolts and the screw of fastening of a dividing lath and shift it forward.
  2. Turn a lath on a quarter of a turn and take out it from a window doorway upwards.
  3. Remove the fixed glass, having pulled for its top corner forward and downwards. Separate from glass consolidation.
  4. Accurately take out upwards from a door glass.
  5. Separate a socket, turn out 4 bolts and remove window raiser through a service aperture.

Necessarily separate a socket to exclude operation possibility window raiser and trauma receptions.

  1. Uncover the lever of blocking of the lock, turn out 4 bolts, separate 2 sockets and remove the lock.
  2. Turn out 2 screws and remove a lock casing.
  3. Turn out two bolts and remove the external handle of a door.
  1. Remove molding.
  1. Remove basic pillows.
  1. Give fixture of loops and the terminator of a door and remove it, preliminary having removed the panel of facing of the central rack of a body. For this purpose remove overlays of thresholds of forward and back doors then liberate from clamps and remove the panel of facing of the central rack of a body.
  1. At installation of the door especially new, it is necessary to adjust its position, operating with a similar case of adjustment of position of a forward door. Efforts of a tightening of bolts are specified in Specifications of the Head the Body.
  2. Installation is made upside-down. Tighten fixture with demanded efforts, use new clamps.